Welcome Y'all! It's that time again for our Creative Craft Hop hosted by Sara @Birdz of a Feather! I don't know if you're like me, but I'm always on the lookout for craft project inspirations! While I was in Target some time ago, I came upon a utensil holder that was made out of seagrass, I think. I loved how it looked so I took pictures of it - just like I usually do when I'm inspired. Unfortunately, it is no longer available at Target, but here is a picture of it:
And that is where I got the idea to make a flatware caddy of my own! Since I collect tin cans and other recyclables for my projects, it was a no brainer to use tin cans to make a caddy - one with three sections or cans, sized for spoons, forks and knives! Cheerful and charming - especially done in purple, lol - this Cord Wrapped Tin Can Flatware Caddy adds a playful element to get-togethers and gatherings. A group of three hand wrapped upcycled tin cans in poly cord that's perfect for entertaining and a whole lot more!
Materials Needed:
- Tin cans - 3 (27oz.)
- Poly Cord
- Quick dry multi purpose glue (Starbond) or hot glue
- Parchment paper
- Ruler
- Drill
- Screws
- Phillips screwdriver (short handle)/rachet
- Wire clothes hanger
- Wire cutter
Let's begin with clean, dry tin cans. I'm using vegetable cans that are a great size at 27 ounces!
Plus, I'm using leftover purple cord from a previous project making this caddy basically cost free! I also like to spread a sheet of parchment paper over my work surface to catch any glue that may fall off. Begin by adding a dab of hot glue to the end of the cord and . . .
coiling it into a circle while adding a bit of glue along the cord as you coil.
Then add a dab of hot glue to the center of the bottom portion of the tin can and continue coiling the poly cord around the can.
At first, I didn't want hot glue to show on the purple cord so I used a high performing super glue called Starbond which dried clear to attach the poly cord.
Continue coiling the poly cord until the bottom is completely covered . . .
and then moving up the sides of the can.I switched to using hot glue since I was running out of Starbond. Continue adding hot glue to wrap the can with poly cord . . .
going round and round until the can is completely covered.Then wrap the other two cans the same as the first.To secure the three cans together, use a drill to create holes near the top of the three cans aligning the holes on the cans with a ruler to match up the holes. Use a short handle Phillips screwdriver or rachet to tighten the screws and attach the cans together. Dab a bit of Starbond glue on the screws to hold in place and let dry.To make the handle, cut off the straight bottom wire of a clothes hanger . . .using a wire cutter.Fold the wire in half, leaving a loop at the top and twisting the wire at the bottom to close.Wrap the loop with cord beginning at the bottom and . . .moving up along the loop and . . .back down to wrap around the bottom again.Then apply glue around the wrapped bottom cord and insert into center of cans. Hold cans together for a couple of minutes until glue dries.
This practical upcycled caddy adds a casual warmth and welcome to the table for both inside and outside entertaining. And as an added plus, the caddy can be used to house all sorts of things like pens and pencils, office supplies and even bottles of wine! It's really a multi- purpose handcrafted item that can be use all year long!
Once again, welcome to our monthly Creative Craft Hop! I hope you liked how I made my cord wrapped flatware caddy! Up next, is Carol @ Bluesky at Home sharing how to make pretty vinyl planters! Be sure to stop by each and everyone in our creative group listed below to check out their exciting and inspiring project! And don't forget to pin, too!
.png)
-003.jpg)
