Wednesday, July 28, 2021

How to Make a String Ball with Bow Ornament


This post first appeared on Bowdabrablog.com where I'm on the Bowdabra Design Team.

Make this adorable string ball ornament to put on your tree this Christmas! It's easily customized with your favorite decorations like this Bowdabra bow! And it's a fun craft to make right now during Christmas in July! 

You can easily make this adorable string ball with bow using  a few items:

First, blow up a balloon to your desired size. Next, I'm going to describe the easiest way I've found to wet the thread and at the same time remove excess glue while wrapping the balloon. Virtually no mess, and it also keeps the string from tangling. Do this by taking a thin upholstery needle and thread it with the end of a ball of crochet thread (don't cut the thread). Next, take a small bottle of Aileen's Tacky glue (Dollar Tree) and punch the lower portion of the bottle with the threaded needle - 

pulling the needle and thread through the bottle. Remove the thread from the needle and tie the end around the knot on the balloon. 
Begin wrapping the balloon with the thread while holding glue bottle - first vertically and .  .  .
then horizontally until you're satisfied with the look. You can add additional tacky glue over the thread by dabbing on with a sponge. Secure the string around the balloon knot, and cut leaving a length to hang. Dry for several hours or overnight. 
Once the string ball is thoroughly dry, pop the balloon with sharp end of scissors.
The balloon will separate from the string ball .  .  .
then pull the deflated balloon out .  .   .


How to make the Bowdabra bow to decorate the top of the string ball:

Fold a 24" piece of Bowdabra bow wire in half and lay in the Bowdabra, tucking ends under. Next, insert sparkling floral stems randomly into the Mini Bowdabra. Then pinch the end of a 1" wide ribbon and insert down into the Bowdabra. Fold over a 2.5" inch loop and press into the Bowdabra. Then fold the ribbon on the opposite side making another 2.5" loop.
Continue making  more 2.5" loops for a total of six on each side. Then scrunch down the ribbon using the Bowdabra wand.
 While the bow is still in the Bowdabra, tie off by threading the two loose ends of the bow wire through the loop at the other end. Pull the bow wire tightly and tie into a knot before removing the bow from the Bowdabra. 
Secure the bow wire with another knot in front while creating a hanging loop - cutting off excess and tying ends in a knot. Fluff out bow and trim. 
Attach to top of string ball with hot glue for the cutest holiday look ever!

Thanks for stopping by

and take a little time to enjoy,

Happy Crafting!

5 comments:

  1. Gail,
    I remember people making Easter eggs using this technique...I never tried it though!! It looks lovely!! Thanks so much for stopping by!! Stay safe, healthy and happy!!
    Hugs,
    Debbie

    ReplyDelete
    Replies
    1. Thanks, Debbie! Yes, it's a very old technique that's getting a revival - like most crafts! It seems what's old is new again!

      Delete
  2. User ought to guarantee that the printer head is spotless and liberated from dust. Residue on the head might cause some deterrent while printing There are two different ways to clear or clean the residue, one being the programmed way and the other the manual one, using the muslin material. 123 setup Doing as such will permit the printer to tackle its work proficiently without stalling out. Try not to give too many print occupations to the HP printer consistently; this might cause a error while printing. Continuously print in ordinary and draft mode from the printer; it will print quicker. Imprinting in higher Dpi or best quality mode will make the HP printer measure a bit lethargic Remove the separators in the archives as this will empower the user to try not to print clear pages at the appointed time of distribution from the HP printer. The paper for printing ought to be clear as it prints quicker. Different papers chose may cause an issue while printing from the hp printer.HP printers empower to print photos to protect every one of the recollections users can print straightforwardly and afterward outline those recollections for the dividers at home or office spaces. Deal with the cartridges of the HP printer and ensure they don't dry out because of a periodic use. Not topping off the cartridges on time can be another justification the cartridge to turn flawed. These vacant cartridges need substitution at the soonest.

    ReplyDelete
  3. Nice and interesting post, I appreciate your hard work, keep uploading more, Thank you for sharing valuable information. Also, Check auction sites like eBay      

    ReplyDelete
  4. Nice and interesting post, I appreciate your hard work, keep uploading more, Thank you for sharing valuable information. Also, Check free eyeglasses         

    ReplyDelete

Related Posts Plugin for WordPress, Blogger...